Mira Escape Betriebsanweisung

1These instructions are to be left with the userInstallation and User GuideTHERMOSTATICELECTRIC SHOWERMIRA ESCAPE

102. Electrical• In a domestic installation, the rating of the electricity supplier’s fuse and the consumer unit must be adequate for the additional

11Double-poleIsolating SwitchConsumer UnitInstallationInstallation of Mira EscapeWarning! Turn off the electrical and water supplies before proceeding

12Three case inserts are supplied with the Mira Escape, so that they can be trimmed to suit the supplies entering the product. Before tting the cover

13Feed cable into Case. Fit Earth sleeve (not supplied) and strip insulation.Do not twist cable cores.Firmly connect the conductors. Do not exert stra

14Cold Water Supply Pipe (Bottom Entry)Service TunnelFixing ScrewHoles For CoverRetaining ScrewsCase InsertElectrical Supply CableTerminal BlockInlet

15CommissioningTurn control to full cold. Turn the water supply fully on.Check for water leaks. Set control to ‘I’. Switch on electrical supply.P

16Turn control to full cold. The temperature will rise slightly.Set control to ‘II’._ + 0 - 10 Secs12.11.10.The temperature will rise further.Adju

17_+COLD_+_+The warmer the shower, the lower the ow rate and vice versa.Heated water is produced by adjusting the ow of cold water passed through a

18The shower's top priority is to keep the desired water temperature constant. Electric showers with thermostatic control are able to keep a stab

19Using your ShowerRead the section “Important Safety Information” rst.Note! At the end of every shower make sure that the shower head points into th

2If you experience any difculty with the installation or operation of your new Electric Shower, please refer to ‘Fault Diagnosis’, before contacting

20Water inlet pressure uctuations due to other draw offs (e.g. ushing toilet). Shower temperature will be controlled to within ± 2°C of the set temp

21Fault DiagnosisThe trouble shooting information tabled below gives details on probable causes and remedies should difculties be encountered whilst

22Symptom Power LightLow Flow LightHeater Setting I/II/IIIProbable Cause Possible RemedyLow or no ow.ON ON ON ONON ONONON ON

23Symptom Power LightLow Flow LightHeater Setting I/II/IIIProbable Cause Possible RemedyWater will not turn off.ON ONOFF ONAny AnyInlet valve, sol

24Make sure that the electrical supply is turned off at the mains and that the water supply is fully turned off.Remove the three screws, the

25FilterHold a wrench across the ats of the metal connector. Unscrew the filter using another wrench as shown. Clean or renew the Filter as neces

26Dimensions90 mm79 mm207 mm340 mm348 mm

27BROWNBROWNBROWNBLUEBLUEGREENGREENBROWNBROWNBROWNBLACKBLACKBLACKREDREDREDWiring DiagramThermal CutoutDual DiscTank ConnectionLoadInlet ConnectorPress

28Spare PartsMira Escape405.58 Inlet Connector Assembly406.27 Inlet Filter (with ‘O’ seal tted)416.38 Clamp Bracket (Inlet)416.48 Latching Switch

29405.58406.27416.381563.719416.48416.51872.01872.281563.5071563.539AAAAAAAAAA1563.6941563.534BB1563.5191563.5441563.5451563.5321563.5331563.5371563.5

3IntroductionThank you for purchasing a quality Mira product. To enjoy the full potential of your new product, please take time to read this guide tho

30AccessoriesEverclear ShowerheadWhite - 2.1616.030Chrome - 2.1616.031Mira's new Everclear range has been specially designed for hard water areas

31Notes

321060688-W2-F (1563) (J95G/H, J95Hb/c) © Kohler Mira Limited, February 2011Customer ServiceGuaranteeYour product has the benefit of our manufa

4Recommended UsageDomesticüLight CommercialüHeavy CommercialûHealthcareûGuaranteeFor domestic installations, Mira Showers guarantee the Mira Escape 9.

5Important Safety InformationWARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:1. Installation of this shower must be carried out in

616. Electric showers can deliver scalding temperatures if not operated, installed or maintained in accordance with the instructions, warnings and ca

7Pack Contents ChecklistMira Escape 3 x Wall Plugs 3 x Fixing Screws 1 x Mira Escape 1 x Compression Nut 1 x Olive 3 x Case InsertsTick the appropriat

8Specifications1. Plumbing• Minimum maintained inlet pressure for 9.0 kW and 9.8 kW 70 kPa (0.7 bar).• 100 kPa (1.0 bar) recommended for satisfactor

9• Avoid layouts where the shower hose will be sharply kinked. This may reduce the life of the hose.• A Soap Dish/Hose Retaining Ring is supplied to